Archive

Posts Tagged ‘3d printing’

Small spool holder for Mendel90

September 10th, 2013 2 comments

After I completed building my Mendel90 I was a bit disappointed when I found out that the spool I had (bought from ultimaker site) was smaller than the spool holder. So I placed the spool on my desk behind the printer and never really bothered to solve the problem. Every now and then during the printing I would manually unroll filament from the spool so I don’t stress the extruder motor.

Well a couple of days ago I was browsing the reprap forums and found a nice extension that solved (well sort of) my problem. Fellow reprapper GerdH created a neat extension design to support multiple spool holder sizes. I downloaded the .scad file, compiled it, sliced it with Cura with my settings and printed it. I had to run to the nearest hardware store and get a set of four screws with nuts. So within few hours I saw the post the spool holder was installed on my printer and its working perfectly. No more manual unrolling of filament!

During printing

During printing

 

The spool where it was meant to be from the beginning!

The spool where it was meant to be from the beginning!

 

Categories: 3D printing Tags: ,

3D printing my balancing robot

April 28th, 2013 No comments

3D Printing Fever!

Hello everyone. Did I tell you I am having a blast with the 3D printer? My god, this thing is wonderful. Is every engineer’s dream come true. Seriously. Anyway, in my last post I told you about putting together a Mendel90 reprap. Since then, I devoted some weekend time to calibrate the machine and I am really satisfied with the results.

As an engineer, my 3D printing time is focused on creating useful and functional parts, rather than something artistic like a complex shape or a small Yoda (even though I would like to print one some day). Anyway, its been some time since I decided to create a balancing robot, a project unfortunately I neglected for too long. So, this will be a nice opportunity to design my own parts and progress on the balancing robot project!

To do that, first I needed a CAD program to design my parts in. I never used a 3D CAD software before, so I went into the wild to see what is available. The features I was interested in are:

  • Run on Linux (Ubuntu)
  • Easy learning curve
  • Price below 50 Euros (or free!)

Let me tell you, there are not that many choices fulfilling the above. I ended up using FreeCAD and I really like it. Until now, it suits my needs, its free and works just fine on my Ubuntu. OK it is a little buggy sometimes but I don’t mind. At the beginning it was a bit difficult to understand how it works, but after I read about the Part Design and Constraints I quickly got the point. I have to admit, Constraints is something I didn’t know it existed in CAD software and after I discovered that I immediately loved it! When I get more experience with FreeCAD I will make a tutorial on the basics. I think it really deserves more visibility.

Designing the parts

When designing parts to be 3D printed on my machine, there are a few things that govern my design. First, the design must be compatible with the 3D extruding printing constraints. You must be careful of steep overhangs. Another thing are the holes. Most of the slicer software has some problem printing small holes accurate. My current calibration gives me hole accuracy 0.4mm(+/-) which is not that good but it hasn’t caused much trouble yet. However, my main concern when designing is the use of filament, for a few reasons. The most obvious one is cost. If you make a really big and heavy part, you could raise the cost to a level which 3D printing it out doesn’t make sense, if you can buy a similar part (robot chassis for example) much cheaper from the web. And keep in mind that you may make mistakes and need to reprint a part 2 or 3 times (even more?) before deciding its the one! What is more important for me though, is printing time. You see, more filament = more printing time! Most of the times I am anxious to try out my latest design and I hate to wait more than 10-15 minutes. So I tend to design, quick-to-print parts. At least for now.

Today’s print: Motor mount

Today, I designed a part used to mount the motors on the chassis. Took some specs from the motor datasheet, and designed the part so it can be screwed on the motor and hold it firmly. So I fired up FreeCAD and some time after, the result is this:

Freecad design

Freecad design

After exporting the .stl file and slicing it with Cura it was ready for printing. The pictures show the result.

Fresh out of the oven!

Fresh out of the oven!

Good alignment of the holes

Good alignment of the holes

Motor screwed on the mount

Motor screwed on the mount

Attached on the chassis

Attached on the chassis

 

Hopefully sometime within next month I will find some time to attach the motor controller and start working on the electronics of the robot.

Until next time…

First steps in 3D printing

February 4th, 2013 No comments

Hello everyone.

About a month ago I was watching a video on youtube about a guy building a robot. At some point that guy set “…I printed these parts on my RepRap…”. Those words echoed in my head, again and again. …… and bam. That was it.

You see, I have watched the progress of 3D printers for some time now. From the moment I saw one online I was hooked. Unfortunately the price was too high for a “toy”. At least that what I was thinking then. I considered it as a “toy” since is something I don’t really need. I wanted it to satisfy my creativity itch. So I decided to bury my 3D printing desire to save some money. And I was good at it. Until it hit me when I watched that video.

Right there I decided I would buy one, no matter what. I agree that spending 600-700 Euros may seem like a lot at the beginning, but let me tell you that the rewarding you get from 3D printing is huge. Talking for myself, its been a long time since I felt that much satisfaction in my tech life experience.

So, I believe that 3D printing is going to be the new part of this blog. To get the ball rolling, my next post will describe the machine I bought and the assembling experience.